June and July each year are the key times for walnut grafting. In particular, the budding technique is adopted, and the survival rate is high. The operation is easy and convenient, and the technology is easy to grasp and popularize. It is suitable for planting small trees and nursery nursery. As long as it operates scientifically and reasonably, it can become a key point for increasing production. â€
Grafting time
It can be done from June to July. During this period, the survival rate of grafting is high and growth is vigorous. Prematurely, the buds on the scion are too tender to survive after grafting; too late, the growth period of shoots after grafting is short, the maturity of new shoots is low, and wintering is difficult.
Prepare before grafting
Choosing scion: Select the buds that are full of lower shoots in the middle of the year. It's best to choose straight shoots, try to avoid bow-shaped and three-cornered new shoots, remove the leaves immediately after cutting and leave 1 cm long petioles for evaporation. It is advisable to pick and choose, but if you can't pick it up, take care of it and put it in a damp and cool place. It should not be stored for more than 72 hours.
Selected rootstocks: When two or more years of actual saplings are selected to grow new shoots, the growth should be greater than 40 cm. Alternatively, one-year-old shoots can also be selected. The diameter of the buds should be greater than 1.2 cm.
Grafting step
Take buds: Take rectangular or square buds. The upper edge of the blade is 1 cm from the upper edge of the bud, and the lower edge of the blade is about 1 cm from the lower edge of the petiole, and the width of the petiole may be equal to or slightly wider on both sides. A standard tool can be used for budding, both accurate and fast.
Rootstock processing: On the selected rootstock, the relatively smooth side is set in a good position, the lower leaves to be opened are all removed, and the upper part is left with 3 to 4 compound leaves for nutrient supply and the extra upper tip is removed. Open a mouth equivalent to the bud, you can open the door alone or double open the door. The lower part of the opening can be 2 to 3 mm more, as a sink for wounds, so as not to hurt the buds.
Stick buds: Immediately put the removed buds into the door, paste them well, compact them and tie them tightly. For Luo Guoshu, buds and doors should pay attention to good, belly to belly, back to back. With a 1.5 cm wide transparent plastic strip, wrap it up from a point 1 cm from the lower edge of the wound, and wrap it around 1 cm from the edge of the knife edge. Tightly pack the buds to prevent water evaporation and rain penetration. Be careful to reveal buds.
7 to 10 days after grafting, survival conditions can be seen, live, buds remain green; dead, buds become brown or black, to be patched in time. From 12 to 13 days, the live buds are obviously enlarged. After germination, germination should be promptly removed in order to provide support.
Cut the rootstock: When the grafted sprouts germinate 3 to 5 cm, leave 3 to 5 cm above the buds and remove the rest. Put the newly sprouted buds gently on the remaining branches to prevent wind breaks. In addition, according to the growth of new shoots, timely dismantling of the tied plastic strips.
Post-grafting management
After cutting off the upper shoots, the sprouts grow very quickly, but autumn is not easy to fall off and the greed is prosperous. Therefore, appropriate measures must be taken to prevent them from freezing. In late August, fertilizer control began to prevent leggy. Pick up the hearts before and after the beginning of autumn to increase the degree of lignification of new shoots. In mid-September, when the leaves have not fallen, it is necessary to artificially promote its aging. Ethephon can spray 50ppm, and the concentration should not be too large.
Each room based on the requirements of the composition of the lighting scene lighting control, the simple operation can be on the smart controller.Scene lighting control system is a system of intelligent control and management of lighting, compared with the traditional lighting, it can realize the lighting soft start and dimming, scene, remote management and zoning lights closed, and available remote control, timing, concentration, and other remote control, even with the computer to the light advanced intelligent control, so as to achieve the intelligent lighting energy saving, environmental protection, comfortable and convenient function.
Scene Lighting Control System,Lighting Controls Systems,Lighting Control Module
Shenzhen Zhuohao Intelligent Electronic Development Co., Ltd. , https://www.szactop-smart.com