For any mechanical equipment, the usual maintenance work is done well, which directly affects the service life of the mechanical equipment. The maintenance of the filter press during use is very important and requires lubrication and maintenance of the mating and transmission parts.
In order to maintain normal operation, we are necessary to maintain and maintain the filter press in daily use. Therefore, we need to pay attention to the following points:
1. Check carefully whether the joints are firm at all times, whether the parts are used well, and notify the maintenance staff to check if abnormal conditions are found.
2. The electronic control system should be tested regularly for reliability and reliability. It is found that the correctness and inflexibility caused by the electrical components are correct and repaired or replaced in time.
3. Check the pull plate trolley, sprocket chain, bearing, piston rod and other parts regularly so that the matching parts are kept clean and the lubrication performance is good, so as to ensure the movement flexibility, the synchronization of the pull plate trolley and the drape of the chain. It is necessary to adjust in time.
4. Always check the sealing surface of the filter plate to ensure it is clean and clean. Before pressing, the filter cloth should be carefully inspected to ensure that it is free from folding, damage, and slag, so that it is well-prepared to ensure filtration. The effect; at the same time, the filter cloth should be washed frequently to ensure the filtration performance of the filter cloth.
5. If it is not used for a long time, the filter plate should be cleaned and drained neatly on the frame of the filter press and pressed with a pressure of 1 to 5 MPa. The filter cloth is dried after drying; the exposed part of the piston rod and the integrated block should be buttered.
6. Hydraulic oil uses HM46 or HM68 and must be kept clean. The new machine should be replaced with hydraulic oil once a week. When changing oil, the hydraulic oil used in the fuel tank and cylinder should be drained and the tank cleaned. Continue to use it after one month and replace it once in the next six months. This will ensure the normal use of the filter press.
7. Maintenance of the hydraulic system, mainly for the inspection and maintenance of the sealing of the hydraulic components and interfaces.
In order to maintain normal operation, we are necessary to maintain and maintain the filter press in daily use. Therefore, we need to pay attention to the following points:
1. Check carefully whether the joints are firm at all times, whether the parts are used well, and notify the maintenance staff to check if abnormal conditions are found.
2. The electronic control system should be tested regularly for reliability and reliability. It is found that the correctness and inflexibility caused by the electrical components are correct and repaired or replaced in time.
3. Check the pull plate trolley, sprocket chain, bearing, piston rod and other parts regularly so that the matching parts are kept clean and the lubrication performance is good, so as to ensure the movement flexibility, the synchronization of the pull plate trolley and the drape of the chain. It is necessary to adjust in time.
4. Always check the sealing surface of the filter plate to ensure it is clean and clean. Before pressing, the filter cloth should be carefully inspected to ensure that it is free from folding, damage, and slag, so that it is well-prepared to ensure filtration. The effect; at the same time, the filter cloth should be washed frequently to ensure the filtration performance of the filter cloth.
5. If it is not used for a long time, the filter plate should be cleaned and drained neatly on the frame of the filter press and pressed with a pressure of 1 to 5 MPa. The filter cloth is dried after drying; the exposed part of the piston rod and the integrated block should be buttered.
6. Hydraulic oil uses HM46 or HM68 and must be kept clean. The new machine should be replaced with hydraulic oil once a week. When changing oil, the hydraulic oil used in the fuel tank and cylinder should be drained and the tank cleaned. Continue to use it after one month and replace it once in the next six months. This will ensure the normal use of the filter press.
7. Maintenance of the hydraulic system, mainly for the inspection and maintenance of the sealing of the hydraulic components and interfaces.
RICTRON Industrial Co., Ltd is a hight-tech OEM/ODM enterprise, we are specialized to produce the products such as fire smoke alarm, carbon monoxiede alarm, gas alarm, water alarm, smoke&co or gas&co combined alarms, and other products of R&D, manufactring and sales since 2008.
Smoke Sensor,Smart Smoke Detector,Smoke Detector Tester,Stand Alone Smoke Detector
Rictron Industrial Co., Ltd , https://www.szrictron.com